2N2219A DATASHEET PDF

2NA Transistor Datasheet pdf, 2NA Equivalent. Parameters and Characteristics. DESCRIPTION. The 2NA and 2NA are silicon Planar. Epitaxial NPN transistors in Jedec TO (for. 2NA) and in Jedec TO (for 2NA). DESCRIPTION. SYMBOL. 2NA. UNIT. Collector -Emitter Voltage. VCEO. V. Collector . Data sheet specifications and its information contained are.

Author: Malarr Fausho
Country: Congo
Language: English (Spanish)
Genre: Software
Published (Last): 22 March 2010
Pages: 258
PDF File Size: 8.5 Mb
ePub File Size: 6.99 Mb
ISBN: 409-5-86906-288-5
Downloads: 66405
Price: Free* [*Free Regsitration Required]
Uploader: Vibei

Where Vcc is the voltage on which the load operates and V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1.

The 2N is a NPN transistor and is normally used as a switch in many circuits. So to calculate the resistor value of the base we can use the formulae.

To make this current flow through the transistor the value of base current I B can be calculated using the below formula: Overall it is just another small signal transistor which is commonly used in switching and amplifying circuits.

2n2219a Drains out through emitter, normally connected to ground.

2N2219A Datasheet, Equivalent, Cross Reference Search

When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. Current flows in through collector, normally connected to load.

  ERCA FORMSEAL PDF

In our case for a collector current of mA we have to pass a base current of 16mA. But it comes in a metal can package and can operate on voltages slightly higher than what a 2N can handle. Where 2n2219 FE, is the current gain of the transistor which in our case is Amplifier modules like Audio amplifiers, signal Amplifier etc.

So if you looking for an NPN transistor that could switch loads or for decent amplification then 2N might the right choice for your project. This stage is called Saturation Region.

2N Transistor Pinout, Specs, Equivalent & Datasheet

The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. But this calculation will lead to the closest value to start with. So the value if R B will be.

Submitted by admin on 21 June TL — Programmable Reference Voltage. As we know the transistor is a current controlled device meaning, we have pass some current I B thorough the base of the transistor to turn it on.

2NA Datasheet, Equivalent, Cross Reference Search. Transistor Catalog

Since transistor is of NPN the load to be switched should be connected to the collector and the emitter should be connected 2n2219q the ground as show in the figure datashwet. To make this current flow through the transistor the value of base current I B can be calculated using the below formula:. Another important thing to keep in mind, while using a transistor as switch is the base resistor.

  HUMPHRY SLOCOMBE ICE CREAM BOOK PDF

This resistor is connected to datadheet base pin of the transistor to limit the current flowing through the base. The value of this current can be calculated by the required amount of current that will be consumed by the load.

Complete Technical Details can be found at the datasheet given at the end of this page.

When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. To bias a transistor we have to supply current to base pin, this current I B should be limited to datashet by using a transistor to the base pin.

However this vale will not be very accurate because the transistor will have an internal voltage drop across the collector current, so it mostly experimental to get the maximum current from the transistor. Here lets us assume the load here consumes around mA maximum so our collector current I C mA.