Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication. Details, datasheet, quote on part number: ADS The ADS, ADS, and the new ADS converters all are designed for specific touch screen. ADSE ti ADS, Touch Screen Controller. FEATURES. q 4-WIRE TOUCH SCREEN INTERFACE q RATIOMETRIC CONVERSION q SINGLE SUPPLY.
|Published (Last):||8 August 2006|
|PDF File Size:||8.61 Mb|
|ePub File Size:||12.72 Mb|
|Price:||Free* [*Free Regsitration Required]|
Thanks for the response Ian I really appreciate it. If I’m not mistaken, how it works is read the X and Y and using if statements as7843 to see if it falls into a certain range and then use one of the map functions that contains an offset for the corresponding range?
Replacing a 4 pin leaded inductor with a 2 pin Started by gkmaia Yesterday at I then check to see which map function I should use and if falls within a certain range I use the center offset that I have stored subtracts 40 and 30?
For example, if I read in datashet, for the center when it is supposed to beHey guys, I could use a bit of help. I calibrate the dead center then each quarter in turn Welcome to our site! Micro New Member Apr 9, You need a map function to work out the TRUE pen position map xLeft, yTop, xcentre,ycentre ; return point 0,0 tomap xcentre,ycentre, xright, yTop ; return pointto ,0 map xLeft, yBottom, xcentre,ycentre ; return point 0, tomap xcentre,ycentre, xright, ybottom ; return pointtoThis will give a good linear reading.
Or do I average the offsets of the center and corners and use that as the “overall” offset? Thread starter Micro Start date Apr 9, Micro New Member Apr 10, I found some sample drivers in the GLCD and touch screen: Datasheets, Manuals or Dahasheet.
ADS datasheet, Pinout ,application circuits 4-wire Touch Screen Controller
Even when it IS placed properly, this can happen. Do you use the uC’s builtin ADC to do this?
It can sometimes be a little crooked as well To participate you need datzsheet register. I’ll try working on it a bit more later today, but your response raised a few questions more questions: This makes it a little more linear. Do I just add or subtract in this case the amount it is off by, and for areas close to the center use that offset and for the corners use their respective offsets?
You must log in or dagasheet to reply here. Click here to register now. Media New media New comments Search media. I found that the touch panel tilts slightly so linear calibration isn’t the best way to go. One other thing when you press the touch wait mS before you read x and y, the ads may do this for you, as the reading settles and changes position. I make my own I have 4 calibrations 5 point calibration If your touch panel doesn’t tilt you can get away with 3 points I’m stuck trying to figure out this controller.
Once you ads7483 those coordinates what exactly do you do with them? Forums New posts Search forums. Also, thank you for clearing up the A2-A0, looking back at the data sheet it makes a bit more sense. I have tried to break it apart a bit and understand it: But to make the most of it I calibrate 4 parts instead of one Sorry for the multitude of questions, but once you have the offsets for the middle and corners do you average the collected offsets?
XPT2046 (ADS7843) – Touch Screen Decoder IC
I have never used this touch controller Calibration is a bit odd. This give the best results Ouch, I can see from the above picture how mechanically the touch screen can sometimes not be properly be placed over the LCD screen, thanks for clearing that up as well.
Oh wow, that’s cool. The first thing you should be doing is displaying the raw data Readx and Ready In general what is the process used with the five offsets? Well, I’m stuck with this controller for now, heh. Articles Top Articles Search resources. From the example I am working off of, I’m a bit confused as to when I actually get the X and the Y data and how it works.
I’ll also be sure and wait ms before reading the values.