The TI CC module is a self-contained wireless network processor that simplifies products and disclaimers thereto appears at the end of this data sheet. The CC WiFi module from Texas Instruments is a small silver The CC is available from Adafruit As a Breakout Board, and as an. Instruments CC transceiver. •. SPI host interface. •. Simple integration with microcontrollers and microprocessors. •. Worldwide acceptance: FCC (USA), IC.

Author: Tojacage Mazunos
Country: Uganda
Language: English (Spanish)
Genre: Marketing
Published (Last): 13 May 2008
Pages: 119
PDF File Size: 16.23 Mb
ePub File Size: 17.58 Mb
ISBN: 315-4-75679-434-7
Downloads: 78392
Price: Free* [*Free Regsitration Required]
Uploader: Shakalkree

Particle Datasheets | Core datasheet

Currently the Core is available in two flavors. All content cx3000 materials on this site are provided “as is”. The external flash memory gives us an additional 2MB of storage space. In most cases, a simple plastic enclosure will not affect the signal strength of the chip antenna.

The connector also acts as an additional heat sink. After setting them up, the user can then write to or read from the pins using digitalWrite and digitalRead functions respectively.

Menu Search through millions of questions and answers User. Some datahseet the key features of the CC module are as follows: If you have a related question, please click the ” Ask a related question ” button in the top right corner. The user can read the pins using analogRead function which returns a 12bit value. No license, either express or implied, by estoppel or otherwise, is granted by TI. All postings and use of the content on this site are subject to the Terms of Use of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms of Use of this site.

The only exception to this are the following pins that are tolerant to 5V inputs:. You can also make your own cantenna!

Pololu – Adafruit CC Wi-Fi Breakout Board with Onboard Ceramic Antenna

D0, D1, D3, D4, D5, D6 and D7 Click here to view a larger pinout diagram Digital pins Each pin on the Core can either be configured as input with or without pull-up or pull-down or as output push-pull or open-drain using the pinMode function. Pins A0 to A7 can be set up as analog inputs and can measure voltages of up to 3. Do you have another question? Please take into account that the voltage levels on these pins runs at 0V to 3.


Ask a related question Ask a new question. We went through a couple of iterations before choosing Microchip’s MCPSE power regulator which comfortably meets the specs. Ask a related question What is a related question?

If you have further questions related to this thread, you may click “Ask a related question” below. This thread has been locked.

You can download the datasheet here. This space is used to store the public and private keys, the factory reset firmware, a back-up firmware and a copy of the firmware sent Over The Air OTA.

The entire Core, including all of the on board peripherals run at 3. Some of its key features are: The RF circuit is probably where we spent the most time on during hardware design. The newly created question will be automatically linked to this question.

Adafruit CC3000 Wi-Fi Shield for Arduino with Onboard Ceramic Antenna

So, in order to power the Core from the USB port or an external power supply, we need to downconvert the datasneet before feeding it into the Core. All of these pins run at 3.

The horizontal spacing between the big ground pads in the middle is listed as 1. Mentions Tags More Cancel.

RF circuit The RF circuit is probably where we spent the most time on during hardware design. In the input mode, the user can activate internal pull-up or pull-down resistors typically equal to 40K ohms. dataaheet

The hardware files for the JTAG shield are available here. I’ve just imported CC footprint from the CCEM layout, and xc3000 checking it, noticed that it does not really comply with datsaheet drawing in the datasheet.


Some of its key features are as follows: Part of the space is also available to the user who can use it to store log data, user parameters, etc. This feature is only available on the following pins: Configuration and use of all of these serial ports is described in the serial functions.

Dattasheet at the top of the memory space is where the bootloader is saved and locked. Here is an updated footprint I’ve received. You could make your own JTAG shield or buy one from us.

Also, note that the maximum read-write endurance is limited tocycles. Is the whole bottom of the module exposed so this does not really matter, or is datasheft amiss?

In reply to Igor Orlovich:.

CC3000 footpring discrepancy between datasheet and EVM

Use of the information on this site may require a license from a third party, or a license from TI. Most antennas that are designed to operate at 2. In reply to Igor Orlovich: SS Datasneet Select A3: Got a direct response from TI- the datasheet does indeed have an error and they are working to fix it.

By default these are deactivated. This version of the Core comes with an on board chip antenna that gives a signal strength similar to a mobile phone. Due to the holidays, responses datwsheet be delayed.

With the on board chip antenna, the peak return loss S11 has been measured and verified to be in the excess of 20dB.

Analog Outputs This term is misleading and misused but is widely adopted in the Arduino community.