IPMP CONFIGURATION SOLARIS 10 PDF

Oracle Solaris Administration: IP Services Oracle Solaris 10 1/13 Information An IPMP configuration typically consists of two or more physical interfaces on the . For IPMP configuration tasks, refer to Chapter 31, Administering IPMP (Tasks). Oracle Solaris IPMP involves the following software: You can configure one of the interfaces down to 10 megabits and still place the two interfaces into the. You must have configured all interfaces as members of the IPMP group. role to a user, see Chapter 2, Working With the Solaris Management Console (Tasks).

Author: Kira Necage
Country: Maldives
Language: English (Spanish)
Genre: Video
Published (Last): 26 November 2010
Pages: 121
PDF File Size: 9.79 Mb
ePub File Size: 11.56 Mb
ISBN: 880-8-36289-326-2
Downloads: 47354
Price: Free* [*Free Regsitration Required]
Uploader: Kataur

Then, the standby interface is treated the same as other active interfaces until the failed interface is repaired.

IPMP Interface Configurations – Oracle Solaris Administration: IP Services

Configure an IP interface into standby mode. This chapter contains the following information: Failure Detection and Failover Failure detection is the process of detecting when an interface or the path from an interface to an Internet configuraion device no longer works. Enable Probe-Based Failure Detection. You do not need to mark an IPv6 test address as deprecated to prevent applications from using the test address.

A L2 broadcast domain typically maps to a specific subnet. Refer to the in. You can always view the current status of an interface by typing the ifconfig interface command. When the failover of address Use the following syntax of the ifconfig command for configuring a test address: The interfaces are configured as members of the same IPMP group. Not all Sun platforms support DR. However, failover and failback cannot occur for an IPMP group with only one interface.

  EL INGLES JURIDICO ALCARAZ VARO PDF

Its really awesome article. Configuring netmasks and default gateway in zones Solaris RCM manages the dynamic reconfiguration of system components.

How to configure Solaris 10 IPMP ? – UnixArena

Because IPv6 link-local addresses are usually not present in a name service, DNS and NIS applications do not use link-local addresses for communication. Planning an IPv6 Network Tasks. Also, no failover occurs when all the target systems fail at the same time.

Finally, RCM fails back any data addresses, just as if the interface had been configurtion. With probe target s defined in the routing table, the in. More Posts from this Category. Data addresses are the conventional IPv4 and IPv6 addresses that are assigned to an interface of a NIC at boot time or manually, through the ifconfig command.

For example, to create an IPv4 test address, you would type the following command: Additionally, RCM informs the in. You can also see that hme1: The following are two common types of IPMP configurations: The attachment of the interface to the IP fonfiguration is down. Additionally, any existing connections to the system using those IP addresses are disrupted.

Configuring an IPv6 Network Tasks 8. The recipient of these addresses is a functioning interface in the failed interface’s IPMP group. For an introduction to test addresses, refer to Test Addresses.

  IX4-200D MANUAL PDF

Chapter 30 Introducing IPMP (Overview)

Paid Training Courses we Offer. IPv4 does not use a deprecated address as a source address for any communication, unless an application explicitly binds to the address. These physical interfaces might or might not be on the same NIC.

Load spreading occurs only when the network traffic is flowing to multiple destinations that use multiple connections. This action is not shown in the examples. During IPMP group configuration, in. A multicast packet that is sent to the all hosts multicast address, To identify the link-local address of an interface, run the ifconfig interface command configuratiom an IPv6-enabled node. Physical interface hme0 with the data address After failback, the original configuration is restored.

How to configure Solaris 10 Probe based IPMP

Consider the example of four VLANs, bgebgebgeand bge The following two examples show a typical configuration and how that configuration automatically changes when an interface fails. You must mark an IPv4 test address as deprecated to prevent applications from using the test address. If a system has multiple interfaces attached to the same link, sloaris can configure IPMP to perform failover if confoguration of the interfaces fails.

Test addresses are configured as logical interfaces of the physical interface that you specify to the ifconfig command.